EN10219 S355J0H LSAW Steel Pipe Welded CS Pipe

EN10219 S355J0H LSAW Steel Pipe Welded CS Pipe

This standard welded pipe is mainly used in high-rise building steel structures, long-span bridges, offshore platforms and other occasions with high requirements for material strength and low temperature toughness, and its excellent welding performance and structural stability make it an important choice for modern steel structure engineering.
Send Inquiry

‌LSAW : Longitudinally Submerged Arc Welded Pipe

1

Core features and advantages

》Welding method: Longitudinal submerged arc welding (SAWL), with a straight weld seam and no spiral weld seam.
》High strength and high toughness: suitable for high pressure, low temperature, and corrosive environments.

Wide range of sizes:
Outer diameter: Φ406 mm to Φ1626 mm (16"–64"), some manufacturers can achieve Φ3000 mm

Wall thickness: 6.0 mm to 75 mm (approximately 1/4"–3")

Length: typically 6M 12 m

Standard certification: Compliant with international standards such as API 5L, ASTM, EN, ISO, GB, DNV, etc

Manufacturing process: mainly including two forming methods, UOE and JCOE.

2

Main application areas

》Oil and gas transmission pipelines: accounting for more than 70% of the usage of LSAW steel pipes, especially suitable for long-distance, large-diameter, and high-pressure transmission
》Structural engineering: such as bridges, wind turbine towers, building support piles, etc
》Pile casing and foundation structure: Compliant with ASTM A252 standard, used for cast-in-place concrete piles or permanent load-bearing structures
》Anticorrosion treatment: Common coatings include 3PE, FBE, epoxy, asphalt, etc., suitable for buried or marine environments

3

Technical Request

EN10219 S355J0H the welded pipe is made of fine-grained unalloyed steel, which requires a minimum yield strength of 355MPa (nominal thickness ≤ 16mm) and a tensile strength of 470-630MPa. 

S: Structural Steel.

355: Minimum yield strength (355 MPa) for wall thicknesses ≤ 16mm.

J0: Impact properties. Guarantees a minimum of 27 Joules at 0°C (Charpy V-notch test).

H: Hollow Section (specifically designed for hollow profiles).

Chemical Composition (Cast Analysis)

For trading purposes, it is important to note the Carbon Equivalent (CEV) value, as it affects weldability. The max CEV for this grade is typically 0.45%

Element Composition % (max) Notes
Carbon (C) ≤ 0.22 Controlled for weldability
Silicon (Si) ≤ 0.55  
Manganese (Mn) ≤ 1.60 Provides strength
Phosphorus (P) ≤ 0.035  
Sulfur (S) ≤ 0.035  
Nitrogen (N) ≤ 0.009  

Mechanical Properties

This is the key selling point for S355J0H: it offers high strength with good low-temperature toughness (0°C).

Property Value Requirement
Yield Strength (ReH) ≥ 355 MPa (t ≤ 16mm)
≥ 345 MPa (16mm < t ≤ 40mm)
Minimum stress for plastic deformation
Tensile Strength (Rm) 470 – 630 MPa Ultimate breaking strength
Elongation ≥ 20% Ductility measure
Impact Toughness (KV) 27 J (at 0°C) Critical for low-temperature applications

 

4

Manufacturing Process

 

LSAW (Longitudinal Submerged Arc Welding) Manufacturing Process
Unlike seamless pipes or ERW (Electric Resistance Welded) pipes, LSAW is specifically used for large diameters and thick walls. It is often referred to as JCOE or UOE depending on the forming process

A. The JCOE Process
1.Edge Milling: Steel plates (skelp) are beveled.

2.Pre-bending: Edges are crimped to ensure weld geometry.

3.J/C/O Forming: The plate is pressed step by step into a "J" shape, then a "C" shape, and finally an "O" shape (cylinder).

4.Submerged Arc Welding (SAW): The seam is welded internally and externally using a granular flux. This process creates a deep penetration weld with a smooth, strong bead.

5.Expanding (Optional): The pipe is mechanically expanded to improve dimensional accuracy and relieve residual stresses

5

Equivalent Grades

Standard Grade Notes
EN 10210 S355J0H Hot-finished version (similar chemistry, different manufacturing)
ASTM (US) A572 Gr. 50 Often used for structural purposes
ASTM (US) A500 Gr. C Cold-formed welded tubing
CSA (Canada) G40.21 350W Structural steel standard
JIS (Japan) STKR490  

 

How To Cooperate With Us?

Our address

Rm1406,14th/F No 208, Hongqi Road, Nankai Dist, Tianjin City ,China

Phone Number( WhatsApp/Wechat)

+86 16622033809

E-mail

alisa@tjshenzhoutong.com

modular-1

Hot Tags: en10219 s355j0h lsaw steel pipe welded cs pipe, China en10219 s355j0h lsaw steel pipe welded cs pipe manufacturers, suppliers, factory, retail lsaw steel pipe, heat resistant steel pipe, steel tube for defense, reliable steel pipe, welded line pipe, ASTM A252 Steel Pipe Casing