Products Description
API 5L Grade B is the foundational carbon steel grade in the API 5L line pipe specification (ISO 3183), with a minimum yield strength of 241 MPa (35 ksi) for PSL1 and 245 MPa (35.5 ksi) for PSL2. This welded line pipe is manufactured in ERW (Electric Resistance Welded), LSAW (Longitudinal Submerged Arc Welded), and SSAW (Spiral Submerged Arc Welded) configurations, covering the full spectrum of onshore and offshore pipeline requirements.
The PSL1 (Product Specification Level 1) designation delivers standard quality for general pipeline service, while PSL2 adds enhanced chemistry control, mandatory Charpy impact testing, maximum yield/tensile limits, and stricter non-destructive examination-making it the specified choice for high-consequence, high-pressure, and sour service applications. This product page consolidates the technical data, export dimensions, coating systems, and application guidance needed for procurement and engineering evaluation.
| Parameter | Specification |
| Manufacturing methods | ERW/HFW, LSAW, SSAW (continuous welding limited under PSL1) |
| Delivery condition | As-rolled, Normalizing rolled (N), Thermomechanical rolled (M), Quenched & Tempered (Q) |
| End finish | Plain end, Beveled end, Threaded end (PSL2: plain/beveled; special coupling per order) |
| Surface condition | Black (bare), Oiled, Painted, or Coated per Section 3 |
| Traceability | PSL1: lot-based; PSL2: heat-based, EN 10204 3.1/3.2 certificate mandatory |
| Manufacturing Route | Typical Outer Diameter | Typical Wall Thickness | Standard Lengths |
| ERW / HFW | 21.3 mm – 660 mm (½″ – 26″) | 1.0 – 20 mm | 5.8 m / 6 m / 11.8 m / 12 m |
| LSAW | 219.1 mm – 1,422 mm (8″ – 56″) | 4.5 – 25.4 mm | 6 m / 12 m / DRL |
| SSAW | 219 mm – 3,600 mm | 3.2 – 25.4 mm | 6 m – 18 m (custom) |
Typical export size table (representative, not exhaustive):
| NPS | OD (mm) | SCH 10 | SCH 20 | SCH 40 / STD | SCH 80 / XS | Common Coating |
| ½″ | 21.3 | 2.11 mm | - | 2.77 mm | 3.73 mm | Galvanized / Black |
| 1″ | 33.4 | 2.77 mm | - | 3.38 mm | 4.55 mm | Galvanized / 3LPE |
| 2″ | 60.3 | 2.77 mm | - | 3.91 mm | 5.54 mm | 3LPE / FBE |
| 3″ | 88.9 | 3.05 mm | - | 5.49 mm | 7.62 mm | 3LPE / FBE |
| 4″ | 114.3 | 3.05 mm | - | 6.02 mm | 8.56 mm | 3LPE / FBE |
| 6″ | 168.3 | 3.40 mm | - | 7.11 mm | 10.97 mm | 3LPE / FBE |
| 8″ | 219.1 | 3.76 mm | - | 8.18 mm | 12.70 mm | 3LPE / FBE |
| 10″ | 273.1 | 4.19 mm | - | 9.27 mm | 15.09 mm | 3LPE / FBE |
| 12″ | 323.9 | 4.57 mm | - | 10.31 mm | 17.48 mm | 3LPE / FBE |
| 16″ | 406.4 | 6.35 mm | - | 12.70 mm | 21.44 mm | 3LPE / FBE |
| 20″ | 508 | 6.35 mm | - | 15.09 mm | 26.19 mm | 3LPE / FBE |
| 24″ | 610 | 6.35 mm | - | 17.48 mm | 30.96 mm | 3LPE / FBE |
packaging & Shipping
- Packing: Bundled with steel strips, plastic end caps for pipe ends; large diameter loose loading
- Surface: Bare black, varnish, or anti-corrosion coating as required
- Shipping port: Tianjin, Qingdao, Shanghai
- Shipping term: FOB, CFR, CIF, DAP, DDP
- MOQ: Small trial order acceptable; bulk order for full container (20GP / 40GP / 40HQ)
- Lead time: Stock sizes 7–15 days; customized production 25–45 days

Technical Specifications
1.Chemical Composition -API 5L GRB:
| Element (wt. %) | PSL1 (Welded, t ≤ 25.0 mm) | PSL2 |
| Carbon (C), max | 0.0026 | 0.0024 |
| Manganese (Mn), max | 0.012 | 0.012 |
| Phosphorus (P), max | 0.0003 | 0.00025 |
| Sulfur (S), max | 0.0003 | 0.00015 |
| Carbon Equivalent (CE) | Not specified | Max per grade / Pcm applicable |
| Vanadium (V), max | per footnote | per grade requirement |
| Niobium (Nb), max | per footnote | per grade requirement |
| Titanium (Ti), max | per footnote | per grade requirement |
Sources: PSL1 welded pipe C max 0.26%, P 0.030%, S 0.030%; PSL2 C max 0.24%, P max 0.025%, S max 0.015%.
PSL2 chemistry significance: The lower sulfur limit reduces hot-cracking risk; the lower phosphorus limit improves fracture toughness; and the carbon equivalent control ensures field weldability without excessive preheat.
2.Mechanical Properties :
| Property | PSL1 Grade B | PSL2 Grade B |
| Yield strength, min | 241 MPa (35 ksi) | 245 MPa (35.5 ksi) |
| Yield strength, max | Not specified | Limited per applicable grade |
| Tensile strength, min | 414 MPa (60 ksi) | 415 MPa (60 ksi) |
| Tensile strength, max | Not specified | Limited (typically ≤ 760 MPa for Gr. B PSL2) |
| Yield-to-Tensile (Y/T) ratio | Not specified | Max 0.93 (grades ≥ X42) |
| Elongation | Minimum per standard | Minimum per standard, stricter acceptance |
| Charpy impact test | Not required | Mandatory - pipe body and weld |
| NDT | Per standard | Stricter acceptance criteria |
PSL2 yield min 245 MPa, tensile min 415 MPa. PSL1 yield min 241 MPa, tensile min 414 MPa. Y/T ratio max 0.93 and mandatory Charpy testing for PSL2.
Why PSL2 limits matter: A Y/T ratio above 0.93 indicates limited strain-hardening capacity, which is a risk in pipelines subject to ground movement, thermal cycling, or seismic loading. PSL1 does not control this parameter.

Anti-Corrosion Coating Systems
1.3LPE (Three-Layer Polyethylene):
3LPE is the default external coating for buried transmission lines, combining a corrosion barrier with a mechanical protection layer.
| Layer | Material | Typical Thickness | Function |
| Layer 1 (primer) | Fusion bonded epoxy (FBE) | 60 – 150 μm | Chemical bond to steel; primary corrosion barrier |
| Layer 2 (adhesive) | Copolymer adhesive | 150 – 250 μm | Bridges polar epoxy and non-polar PE |
| Layer 3 (outer) | MDPE / HDPE | 1.5 – 3.0 mm | Mechanical protection; impact & moisture barrier |
| Total system | - | 1.8 – 4.7 mm (by DN / duty class) | - |
Layer thicknesses: FBE 60–150 μm, adhesive 150–250 μm, PE 1.5–3.0 mm. Total coating 1.8–4.7 mm depending on grade and duty class. Governing standards: DIN 30670, ISO 21809-1, GB/T 23257.
DIN 30670 minimum total thickness by pipe size (Normal / Reinforced grade): ≤ DN 100: 1.8 / 2.5 mm; DN 100–250: 2.0 / 2.7 mm; DN 250–500: 2.2 / 2.9 mm; DN 500–800: 2.5 / 3.2 mm; ≥ DN 800: 3.0 / 3.7 mm.
Best fit: Long buried onshore lines; rocky backfill; soil movement. Limitation: Thin epoxy underlayer concentrates cathodic protection current at holidays-field joint quality and post-construction coating defect survey are critical.
2. FBE (Fusion Bonded Epoxy):
Single-layer FBE is a powdered thermoset applied electrostatically to heated, blast-cleaned pipe, melting and curing into a continuous chemically bonded film.
| Parameter | Typical Specification |
| External thickness | 300 – 600 μm (standard grades) |
| Continuous service temperature | ~85 °C (standard); high-temp grades above |
| Bonding mechanism | Chemical bond across entire surface - no interlayer to disbond |
| Cathodic disbondment resistance | Good when applied within process window |
| Governing standards | AWWA C210, AWWA C213, AS/NZS 3862, CAN/CSA Z245.20 |
FBE standard thickness 300–600 μm; service ceiling near 85 °C for standard grades. Standards reference: AWWA C210 / C213, CAN/CSA Z245.20. Best fit: High-temperature service, applications where mechanical layer of 3LPE is unnecessary, and girth-weld-compatible systems.
3. Hot-Dip Galvanizing:
Hot-dip galvanizing provides zinc-based sacrificial protection for atmospheric, above-ground, and lower-pressure service.
| Parameter | Typical Export Specification |
| Zinc coating mass (double-sided) | 200 – 500 g/m² (hot-dipped); standard ranges 230–460 g/m² |
| Coating thickness equivalent | ~30 – 65 μm depending on mass |
| Process | Hot-dipped (immersion) or pre-galvanized (strip) |
| Typical application | Water lines, construction, low-pressure gas/air, scaffolding, piling |
Hot-dipped zinc coating commonly quoted at 200–500 g/m²; pre-galvanized 60–150 g/m²; specific export grades at 230 g/m² and 460–600 g/m² double-sided
4.Black Paint, Varnish & Oiling:
| Finish | Description | Typical Use |
| Black paint / bitumen | Asphalt-based or synthetic black coating | Temporary/protection during storage & transport; low-cost external finish |
| Varnish | Clear or pigmented protective lacquer | Mill finish protection; identification preservation |
| Oiling | Light oil film (internal/external) | Short-term rust prevention during shipment; removed before coating or service |
These finishes are non-barrier systems-they protect against atmospheric corrosion during transit and short-term storage, not against long-term soil or immersion exposure. They are frequently specified on PSL1 Grade B pipe for general water or low-pressure service where a full 3LPE or FBE system is not economically justified.
Applications
API 5L Grade B welded pipe serves the full pipeline transportation chain:
| Sector | Specific Applications | Typical PSL / Coating |
| Oil & Gas Transmission | Onshore cross-country transmission lines; gathering and flow lines; gas distribution networks | PSL2 / 3LPE or FBE |
| Offshore & Subsea | Offshore pipelines; subsea flowlines (DNV-OS-F101 typically mandates PSL2) | PSL2 / 3LPE or FBE + concrete weight coat |
| Water & Sewage | Water transmission mains; sewage force mains; drainage | PSL1 / Galvanized or 3LPE |
| Mineral Slurry | Abrasive slurry pipelines; mine tailings lines | PSL1/PSL2 / 3LPE (reinforced grade) |
| Petroleum & Natural Gas Industries | Low-pressure liquid delivery; gas and oil transport in oil/gas fields | PSL1 or PSL2 / per project |
| Construction & Piling | Structural piling; foundation pipe; general construction | PSL1 / Black or galvanized |
| Chemical & Industrial | Process water; low/medium-pressure fluid transfer; machinery manufacturing | PSL1 / Galvanized or black |
Applications span oil and gas pipelines, water and sewage pipelines, and mineral slurry pipelines; low-pressure liquid delivery (water, gas, oil) and construction/piling; petroleum and natural gas transportation.
PSL selection guidance: PSL1 is appropriate for low-pressure gathering, non-critical water distribution, temporary lines, and cost-driven applications with low failure consequences. PSL2 is required or recommended for cross-country oil/gas transmission, offshore/subsea service, sour service (Annex H, HIC/SSC testing), high-pressure gas transmission, and any pipeline in a High Consequence Area (HCA).
FAQ
Q1: What is the core difference between PSL1 and PSL2 for Grade B welded pipe?
PSL2 imposes maximum as well as minimum yield and tensile strength limits, mandatory Charpy impact testing on both pipe body and weld, tighter chemistry (C max 0.24% vs 0.26%; S max 0.015% vs 0.030%; P max 0.025% vs 0.030%), mandatory NDT with stricter acceptance criteria, heat-based traceability, and EN 10204 3.1/3.2 mill certificates. PSL1 provides minimum mechanical properties and chemistry limits suitable for standard service, with NDT and traceability only when specified.
Q2: How much more does PSL2 cost, and when is it justified?
PSL2 pipe typically costs 5–15% more than PSL1 for the same grade and size, driven by tighter chemistry control, additional testing, and lower mill yield (more rejections). The premium is justified when the pipeline carries high-consequence risk-cross-country transmission, offshore/subsea, sour service, high-pressure gas, or HCA-regulated routes-where the cost of failure far exceeds the pipe price differential.
Q3: Can API 5L Grade B pipe be supplied with 3LPE and FBE on the same order?
Yes. Mills routinely apply 3LPE to the external surface and FBE or liquid epoxy to the internal surface (or vice versa) in a single production sequence. However, the two systems serve different functions: 3LPE is an external mechanical + corrosion barrier for buried service; internal FBE or liquid epoxy addresses internal corrosion/flow efficiency. Specify both coating systems and their respective standards (e.g., DIN 30670 external, AWWA C210 internal) on the purchase order.
Q4: What does "black" or "oiled" finish mean, and is it acceptable for buried service?
"Black" refers to a bare mill finish or black paint/bitumen coating; "oiled" indicates a light oil film applied for short-term rust prevention during shipment. Neither is a long-term barrier coating. For direct burial, a 3LPE, FBE, or galvanized system should be specified. Black/oiled finishes are appropriate for above-ground temporary service, storage, or applications where the pipe will be coated after fabrication.
Q5: What is the maximum size available in welded construction?
Welded API 5L Grade B pipe is produced up to OD 3,600 mm (approx. 142″) in SSAW construction and OD 1,422 mm (56″) in LSAW. ERW is typically limited to OD 660 mm (26″). The practical upper bound for a given project depends on wall thickness, length, coating availability, and transport logistics-SSAW large-diameter pipe is commonly supplied in lengths up to 18 m, while ERW is typically 12 m maximum.
Q6: Does PSL2 Grade B pipe require impact testing at a specific temperature?
PSL2 mandates Charpy impact testing, but the test temperature is specified by the purchaser based on the design minimum service temperature. If no temperature is specified, the standard default applies. For sour service (Annex H) , additional HIC (NACE TM0284) and SSC (NACE TM0177) testing is required beyond the base PSL2 Charpy regime.
Q7: What documentation accompanies an export order?
Standard export documentation for PSL2 includes: EN 10204 3.1 mill test certificate (heat-traceable, with chemical, tensile, and Charpy results); NDT reports (UT/RT per applicable SR); coating inspection records (thickness, holiday, peel/adhesion, cathodic disbondment); and dimensional inspection reports. PSL1 orders receive a test certificate traceable to lot, with NDT and SR15 certification only if explicitly ordered.
Our address
Rm1406,14th/F No 208, Hongqi Road, Nankai Dist, Tianjin City ,China
Phone Number(whatsApp/Wechat)
+8616622033809
alisa@tjshenzhoutong.com

Hot Tags: api 5l grb psl1 psl2 erw steel pipe sch40 sch80 line pipe, China api 5l grb psl1 psl2 erw steel pipe sch40 sch80 line pipe manufacturers, suppliers, factory, erw pipe for building envelopes, erw pipe for cold water pipes, erw pipe for pulleys, erw pipe for screws, erw pipe for temporary structures, industrial erw pipe


