API 5L X56 Seamless Line Pipe PSL1 PSL2

API 5L X56 Seamless Line Pipe PSL1 PSL2

Products Description API 5L X56 (designated L390) seamless line pipe is carbon steel seamless pipe engineered for onshore and offshore pipeline transportation of oil, natural gas and associated fluids. It is supplied in two quality levels: PSL1 (general service) and PSL2 (critical service with...
Send Inquiry

Products Description

API 5L X56 (designated L390) seamless line pipe is carbon steel seamless pipe engineered for onshore and offshore pipeline transportation of oil, natural gas and associated fluids. It is supplied in two quality levels: PSL1 (general service) and PSL2 (critical service with stricter mandatory testing). X56 means minimum specified yield strength 390 MPa (56 ksi).
Seamless construction eliminates longitudinal weld seam risk, delivering good toughness, uniform wall thickness and reliable performance under pressure.

NPS OD (mm) SCH 10 WT (mm) SCH 40/STD WT (mm) SCH 80/XS WT (mm) SCH 160 WT (mm)
½″ 21.3 2.77 2.77 3.73 4.78
1″ 33.4 3.38 3.38 4.55 6.35
2″ 60.3 3.91 3.91 5.54 8.74
3″ 88.9 - 5.49 7.62 11.13
4″ 114.3 - 6.02 8.56 13.49
6″ 168.3 - 7.11 10.97 18.26
8″ 219.1 6.35 8.18 12.7 23.01
10″ 273.1 6.35 9.27 15.09 25.4
12″ 323.9 6.35 10.31 17.48 -
14″ 355.6 6.35 11.13 19.05 -
16″ 406.4 6.35 12.7 21.44 -

IMG66131 

Technical Specifications

1.PSL1 vs. PSL2 - Key Differences:

API 5L defines two Product Specification Levels. PSL2 imposes stricter requirements across chemistry, mechanical property ceilings, impact testing, and non-destructive examination .

Requirement PSL1 PSL2
Carbon (C), max 0.28% 0.24%
Phosphorus (P), max 0.03% 0.03%
Sulfur (S), max 0.03% 0.02%
Yield strength, min ≥386 MPa 386–545 MPa
Tensile strength, min ≥490 MPa 490–760 MPa
Maximum tensile strength Not specified Specified (760 MPa)
Yield-to-tensile ratio Not specified ≤0.93
Charpy V-notch impact test Not required Mandatory
NDT General requirements Enhanced UT / specific acceptance criteria
Carbon equivalent control Not explicitly capped CE / Pcm limits apply

Data compiled from mill and industry sources . PSL2 is the appropriate specification for offshore, arctic, high-pressure, sour service, and any application where fracture control and weldability documentation are project requirements .

2. Chemical Composition (X56):

Element PSL1, max (%) PSL2, max (%) Typical PSL2 range (%)
C 0.28 0.24 0.10–0.16
Mn 1.4 1.4 1.30–1.60
P 0.03 0.025 ≤0.025
S 0.03 0.015 ≤0.015
Nb - - 0.03–0.07
V - - 0.04–0.10
Ti - - 0.01–0.03 (optional)
CE (Pcm) - Limited ~0.20–0.22

Sources: API 5L chemical limits and typical X56 micro-alloying practice . X56 chemistry is designed around Nb-V micro-alloying with optional Ti for grain refinement. Carbon equivalent is typically maintained in the 0.38–0.42 range (IIW) or 0.20–0.22 (Pcm), supporting good field weldability .

3.Mechanical Properties:

Property PSL1 requirement PSL2 requirement
Yield strength, Rt0.5 ≥386 MPa (56 ksi) 386–545 MPa (56–79 ksi)
Tensile strength, Rm ≥490 MPa (71 ksi) 490–760 MPa (71–110 ksi)
Yield-to-tensile ratio Not specified ≤0.93
Elongation Per API 5L, based on specimen Per API 5L, based on specimen
Charpy V-notch Not required Required; energy per size/design temperature

 Mechanical property windows from API 5L tables . Typical PSL2 Charpy toughness is specified in the range of 40–50 J average at test temperatures of −10°C to 0°C, with shear area commonly ≥70% 

4.Tolerances and delivery condition:

Item Standard tolerance / option
OD tolerance (D < 60.3 mm) ±0.41 mm / −0.80 mm (typical)
OD tolerance (D ≥ 60.3 mm) ±1% or per API 5L
WT tolerance +15% / −12.5% (typical for seamless)
Length ±200 mm general; ±25.4 mm special
Straightness ≤0.15% of length; ≤0.3 mm/m at pipe end
Ends Plain, beveled, threaded
Surface Bare, black varnish, 3PE/3PP, FBE
Packing Bundled / in bulk; plastic caps; waterproof paper; steel frame or container

IMG66081IMG66121

Applications

API 5L X56 seamless pipe is specified where a moderate strength increase over X52 is required and where PSL2-level toughness and weldability documentation are needed.

Application Why X56 fits
High-pressure gas transmission lines Strength positioned between X52 and X60 for operating pressures typically in the 1,000–1,500 psi range
Offshore flowlines / deepwater Collapse resistance under high external pressure; suitable for 500–2,000 ft water depth where wall thickness and weight reduction matter
Steep terrain / mountainous pipelines Higher strength accommodates mechanical stresses from elevation change with reduced wall thickness
Arctic / low-temperature pipelines Good toughness down to approximately −30°C with appropriate processing and PSL2 Charpy testing
Crude oil trunk lines and product lines PSL2 impact testing and NDT support fracture control in populated or sensitive corridors
Water injection and gathering lines Seamless body eliminates longitudinal weld risk in cyclic and high-integrity upstream service
Pipeline re-ratings / pressure upgrades Upgrading existing lines safely without replacing with a higher grade

For sour service, X56 can be supplied with controlled sulfur (typically <0.002%), calcium treatment, hardness control (≤250 HV10), and HIC/SSC testing where specified .

FAQ

Q1: Should I order PSL1 or PSL2 for my project?
PSL2 is recommended for offshore, arctic, high-pressure gas, sour service, and any project requiring impact test certification, maximum strength ceilings, or full NDT records. PSL1 may be adequate for lower-pressure, non-critical onshore water or utility lines where impact toughness and enhanced inspection are not specified .

Q2: Does PSL2 always require Charpy impact testing?
Yes. PSL2 mandates Charpy V-notch testing at the specified design temperature. Minimum absorbed energy is agreed based on pipe size and service temperature; typical specifications call for 40–50 J average .

Q3: Can X56 SMLS be supplied for sour service (H₂S)?
Yes, with supplementary requirements. Sour service X56 typically requires sulfur ≤0.002%, calcium treatment for inclusion shape control, hardness maximum (e.g., ≤250 HV10), and HIC/SSC testing in accordance with NACE MR0175 / ISO 15156 .

Q4: What is the maximum size available in seamless X56?
Seamless X56 is commonly available from ½″ through approximately 24″ OD. Above 24″, X56 is more frequently supplied as welded (ERW, LSAW) product; seamless availability in larger diameters depends on mill capability and should be confirmed at enquiry .

Q5: How does X56 weldability compare to X52 and X60?
X56 PSL2 chemistry is controlled to a typical CE of approximately 0.38–0.42 (IIW) or Pcm ~0.20–0.22. Preheat may be required for wall thickness above approximately 20 mm. Matching strength filler metals include E8018 / E9018 or equivalent wires. Heat input control is important for HAZ toughness .

Q6: What documentation is typically provided with PSL2 X56 SMLS?
PSL2 orders normally include a 3.1 / 3.2 inspection certificate, heat-number traceability, tensile and Charpy test reports, hydrostatic test records, and NDT reports (UT/EMI) as specified. Hydrostatic testing is performed on every pipe, with hold times per API 5L .

Q7: Can X56 be used at low temperature?
With appropriate PSL2 processing and Charpy testing, X56 maintains good toughness down to approximately −30°C. For lower design temperatures or fracture-control-critical service, drop-weight tear testing (DWTT) and project-specific impact energy requirements may be specified .

How To Cooperate With Us?

Our address

Rm1406,14th/F No 208, Hongqi Road, Nankai Dist, Tianjin City ,China

Phone Number(whatsApp/Wechat)

+8616622033809

E-mail

alisa@tjshenzhoutong.com

p202608281100161ff05webp

 

 

Hot Tags: api 5l x56 seamless line pipe psl1 psl2, China api 5l x56 seamless line pipe psl1 psl2 manufacturers, suppliers, factory, seamless pipe for duct connection, seamless pipe for hydraulic systems, seamless pipe for limiter connection, seamless pipe for mining, seamless pipe for optical connection, seamless pipe for reserve operation system connection